Menu
Refill, fit or filter? Compare four drinking-water choices

What to check on your water softener after a power cut

By Limescale Logic · Published 9 November 2026 · Editorial policy

Short answer: after a power cut, look for leaks, note what the display shows, and find the exact model manual before you touch any settings. A flashing or wrong clock is common to some models, but it does not prove a fault, and what happens next is model-specific. If you are unsure, observe and contact the manufacturer or installer rather than experimenting.

Source guidance checked 9 November 2026.

What a power interruption can affect

A softener with an electronic control may use mains power for its display, clock, valve motor and regeneration timing. A power cut could affect the time of day, the display, or the timing of the next regeneration. Whether anything is lost, kept or delayed depends on the design.

Two manufacturer manuals show how much models differ:

  • The BWT S10/SF2 manual says the display may flash when power returns, that the time of day needs resetting if power was off for more than six hours, and that programmed parameters are retained. That six hour figure applies to that model only.
  • The BWT Perla manual says its AQA Safe valve closes the waste-water valve in a power failure, its control valves remain in their current operating condition, and its programmed parameters are stored permanently and remain unaffected. These are facts for that model only.

Those are examples of why exact-model behaviour differs, not rules. Another make, or another BWT model, may behave differently. Use the BWT UK manuals hub if you have a BWT unit, or the maker's own site otherwise. Identify the exact model, then follow its instructions rather than another model's reset, time or regeneration steps.

What you might see, and what it may mean

On a small screen, scroll the table sideways to see every column.

What you seeWhat it may meanWhat to check next
Flashing time or daySome models flash to show the clock needs attention after power returns. It is consistent with a power interruption but is not a diagnosis.Find the exact model manual and read its section on power failure.
Wrong time of dayThe clock may have stopped or restarted. On some models this could shift when regeneration happens.Check the manual for how the time is set and whether it affects regeneration. Do not guess settings.
Blank displayPower may not have returned to the unit, or the unit may have a problem. A blank screen alone proves nothing.Check whether other appliances on the same supply work. Note what you find. Do not open the unit.
Programming looks unchangedThe model may retain programmed values. Not all do.Compare against any settings you or the installer wrote down earlier.
Regeneration seems late or missingSome models may delay or reschedule it after an interruption. Others may behave differently.Note the time, then check what your manual says about delayed regeneration.
Error codeCodes are manufacturer-specific. On the S10/SF2, the manual says E1 to E7 require service contact.Photograph the code and look it up in your own manual only.
Water on the floorA leak needs attention regardless of the power cut.See the stop and get help section below.

A safe check sequence

  1. Look before you touch. Check the floor and surrounding area for water, and check for any burning smell. If either is present, go to the help section below.
  2. Keep your hands off the internals. Do not remove covers, do not touch wiring, and do not undo hoses or change plumbing.
  3. Photograph the display as it is, including any flashing figures or codes, before pressing anything.
  4. Note the time. Write down the real time, the time shown, and roughly when the power went off and returned.
  5. Identify the model. Read the label or front panel, and find the matching manual from the maker or the installer's paperwork.
  6. Read the power failure section of that manual. Look for what it says about the clock, retained settings and regeneration.
  7. Only follow steps the manual gives for your model. Do not guess settings, do not copy settings from another model, and do not run repeated manual regenerations. Start a manual regeneration only if your exact manual explicitly calls for one.
  8. Check the unit is still on mains. Without opening anything, see whether the unit appears to have power and whether the display is stable.
  9. Observe for a day or two. Watch for changes in the display, any odd noise, or leaks, and note them.

Clock, retained programming, delayed regeneration and error codes

Clock and date. Some units hold the time through a short cut and others need resetting. The S10/SF2 manual ties resetting to a power-off period of more than six hours, while the Perla manual describes different power failure behaviour for that model. These cannot be applied to other models.

Retained programming. Programmed values such as hardness settings may or may not survive. If you do not have a record of the original settings, ask the installer or manufacturer rather than reconstructing them from memory.

Delayed regeneration. If the clock is wrong, regeneration could occur at a different time than intended on some models. Whether yours does so needs checking in its own manual.

Error codes. A code is the unit's own message and its meaning belongs to that make and model. The S10/SF2 manual says E1 to E7 require service contact. A code after a power cut may be worth reporting, but do not assume the cause.

When to stop and get help

Stop using the unit as far as the exact manual permits, and seek qualified help, if:

  • water is escaping or property is being damaged;
  • there is a burning smell;
  • the unit repeatedly loses power;
  • an error persists or returns after you have followed the manual.

If leaking water has reached a plug, socket, wiring or the softener's electrical equipment, do not touch wet electrical equipment or exposed wiring. Keep clear and obtain qualified electrical help. Electrical Safety First flooding advice warns against touching exposed wiring or entering water where live electrical hazards may exist, and says damaged electrical items should not simply be switched on but assessed by a qualified electrician.

For the softener itself, contact the manufacturer or installer. For fixed plumbing or a leak on the pipework, a competent plumber may be appropriate.

Evidence log for the manufacturer or installer

  • Make, model and serial number from the label.
  • Date and approximate times the power went off and came back.
  • Photographs of the display before and after you touched anything.
  • Any error code, exactly as shown.
  • What the manual says about power failure, with the page or section.
  • Any settings you changed, when, and why.
  • Leaks, noises, smells or pressure changes, with dates.
  • Whether the water seems harder, and when you noticed.

This lets a technician see what changed without relying on memory, and it helps you avoid paying for a visit that a manual step would have covered.

Sources

  • BWT UK manuals hub: use the exact model's own operating instructions.
  • BWT S10/SF2 manual: flashing display, time reset after more than six hours, retained parameters, E1 to E7 service contact, for that model only.
  • BWT Perla manual: AQA Safe valve closes the waste-water valve in a power failure, control valves remain in their current operating condition, programmed parameters stored permanently, for that model only.
  • Electrical Safety First flooding advice: exposed wiring, floodwater hazards and damaged electrical items.

Related guides