Is your water softener actually using salt? How to check before you call for service
By Limescale Logic · Published 7 November 2026 · Editorial policy
An apparently unchanged salt level does not, by itself, prove a fault. How quickly salt is consumed depends on the model, its settings, your water hardness, how much water the household uses and how often the unit regenerates. This guide covers how to verify consumption and what to note down. For routine care, see our salt maintenance guide. If soft water is the main worry, see water still hard after a softener.
Why the level can look unchanged
Several ordinary things can hide consumption:
- Low water use. A small household, or one away often, triggers fewer regenerations, so very little salt is used between glances.
- Long intervals. If the unit regenerates every few days, a daily look will not show change.
- Gradual dissolving. The BWT S10/SF2 manual notes that salt dissolves gradually, so the surface can look similar for some time.
- Bridging or a crust. The top layer can look intact while there is a gap beneath. Do not poke or break up the salt yourself. If you suspect this, mention it to the installer or manufacturer.
- Topping up often. Frequent small top-ups make it hard to judge real use.
Timed and metered regeneration
Some softeners regenerate on a timer, others according to measured water use. The BWT S10/SF2 manual distinguishes timed and metered controls, and says household use varies. On a timed unit, salt use should follow a fairly regular pattern whatever the household does. On a metered unit, use rises and falls with water consumption. Other makes may work differently, so use the exact manual for your make and model rather than assuming either type.
A first-check sequence
- Find the exact manual. Note the make and model from the rating label. BWT lists current manuals on its UK manuals page; other manufacturers publish their own.
- Check power and display, where relevant. If your model has a display, see whether it is lit and showing normal information. Note any code exactly as shown.
- Confirm the unit is in service, not bypass. Check the bypass valve position against the manual. If it is bypassed, water is not being softened. Only move it if the manual describes how.
- Check the programmed hardness, only if the manual says users can view it. Look without changing anything. If a value seems wrong, record it rather than editing blindly.
- Mark and date the salt level (see below).
- Test hardness at a known softened outlet (see below).
- Record what you see for the observation period your manual gives.
Marking and photographing the salt level
With the lid open and the salt dry and visible, take a photo showing the salt surface against a fixed reference, such as the inside rim or a fill line if the tank has one. Write the date and the level on a note. Avoid topping up during the observation period, unless the level becomes low. Then compare using the interval in your manual. The BWT S10/SF2 manual gives a visual salt check interval of 3 to 6 weeks depending on usage for that model. Treat that as an example for that model only, not a rule for others.
The Aqua-Dial SoftLife manual similarly says top-up frequency depends on individual household use, and that you should keep the unit topped up with the salt specified for that model.
Checking whether regeneration is happening
The Aqua-Dial SoftLife manual says regeneration may be indicated by water running to drain and by model-specific display codes. If you can safely observe a drain pipe or hear water running at the time your manual says regeneration occurs, note the date and time. Do not run repeated manual regenerations. A single manual regeneration is appropriate only if your exact manual or a support technician specifically directs it.
Testing hardness properly
Existing limescale does not vanish immediately once a softener works, and soap feel is not a reliable test on its own. Use a consistent method instead. Test the same outlet, run the tap briefly each time, and use the same kit. Choose a tap that should be softened, and compare with an unsoftened source such as a kitchen drinking water tap, if your home has one. Our guides on checking water hardness and how hardness is measured explain the units and methods. The Drinking Water Inspectorate notes that hardness varies by supply, so a supplier result or a consistent test is more useful than judging by old scale or feel alone.
Evidence table
On a small screen, scroll the table sideways to see every column.
| Observation | What it may mean | Safe next step |
|---|---|---|
| Salt level unchanged after a few days | Low use or a long regeneration interval; too soon to judge | Keep the dated photo and wait for the manual's observation period |
| Unchanged after the full period, with soft water at the test tap | Very low use, or the unit is working with little demand | Keep records and continue routine checks |
| Unchanged after the full period, with hard water at the test tap | Bypass, no regeneration, wrong settings or a fault | Check service position and display, then contact the installer with your notes |
| Salt drops quickly | High use, high hardness setting or frequent regeneration | Record dates and check the manual's settings description without changing them |
| Display blank or showing a code | Power issue or a model-specific error | Note the exact code and refer to the manual and service |
| Hard water but old scale still visible | Existing deposits remain after softening begins | Rely on a consistent hardness test, not appearance |
When to stop and call for help
Contact the installer or manufacturer if you notice any of the following:
- Leaks, dripping or overflow. See softener overflow and dripping.
- Water draining continuously. See softener keeps draining.
- An error code that returns. The Aqua-Dial SoftLife manual says error codes should be referred to service.
- An unexplained high water level in the salt tank.
- No soft water after the basic checks in your model's manual.
- Uncertainty about valves or settings.
Do not dismantle valves, open electrical parts, change programming without guidance, pour chemicals into the cabinet or break up salt.
What to send with your enquiry
- Make, model and the manual you used
- Dated photos of the salt level at the start and end of the period
- Type of salt used and the dates of any top-ups
- Any display codes, exactly as shown
- Whether the unit was in service or bypass
- Hardness test results, with the tap and date
- Any signs of draining, leaks or noise
You can pass this on through our contact page if you need help deciding the next step.
Sources checked
- BWT UK manuals page
- Aqua-Dial SoftLife manual
- BWT S10/SF2 manual
- Drinking Water Inspectorate: water hardness
Source guidance checked 7 November 2026.
